| 1972 Chevrolet Corvette |
| Numbers matching, 350cid motor overhauled approximately 300 miles ago with standard bore, factory 4 speed, tilt telescopic steering column, suspension, steering, brakes, cooling system, differential and exhaust completely overhauled to factory specifications. Solid frame, no rust, original interior. Older repaint that still shows good. Turn key needs nothing. Runs and drives like a new car. Approximately $30,000 cdn cost for mechanical restoration. This was a good solid car to start with before the mechanical restoration was undertaken one nice corvette motor and differential overhaul were sublet to teha mechanical services. (renowned engine builder) see attached photo invoice. All other repairs done in house by a licenced journeyman red seal mechanic with many years experience. $59,900 cdn parts replaced oil filter & environment tax, wiper blades, washer pump kit, oil & environment tax, emergency brake parts, (top flight / extra mile), outside mirror kit, nut, antenna bezel (ecklers), ignition wire grommet (ecklers), cable, ant lead (ecklers), ball joint upper (ecklers), ball joint lower (ecklers), gasket (ecklers), antenna bezel non-power (ecklers), master antenna bezel non-power (ecklers), expansion tank (corvette central), no front AC front coil spring (corvette central), rear shock mount bracket (corvette central), steel park brake rebuild (corvette central), rear suspension hardware -repl bolts (corvette central), expansion tank strap (corvette central), polished aluminum valve cover (corvette central), oil fill cap-chrome (corvette central), sb expansion tank/rad cap (corvette central), upper & lower a-arm bushing (corvette central), aluminum valve cover pcv valve (corvette central), pcv aluminum valve cover gromment (corvette central), aluminum valve cover emblem (corvette central), a-arm shim (corvette central), bearings, brake hose, seal, control arm bushing install tool, trailing arm align shim, exhaust bezel, delux sb 4spd exhaust, exhaust heat riser valve, exhaust hear riser gasket, exhaust extensions, muffler exhaust hanger, magnaflow muffler, 2 1/2 4 spd sb front, 2 1/2 4 spd intermediate pipe, 2 1/2 centre exhaust hanger, wiper arm - correct, washer hose fluid filter, rh verticle ignition shield w/ j-nut, wiper vacuum switch on firewall, 4 spd neutral safety switch - pedal, seat pivot bolt plastic bushing, seat back pivot bolt w/nut, spark plug wire grommet - oval, no av mirror mount gasket, battery hold down rear reinforcement, battery hold down bolt, seals, brake hose, rear strut rod bushing set 4 pc, trailing arm bushing kit, rear strut rod bushing cap, brake pad - front, brake pad - rear, master cylinder, manifold gasket set, bearing, gasket, thermostat, bearing , altern/gen holder assembly, sway bar link, bushing, valve cover gasket set, pvc grommet, oil filled cap, spark plugs, brake & clutch bushing, rear spindle washer, spindle nut, rear spindle inner bearing shield, drain cock gm, power steering cylinder (new), stardard rear spring, replacement spring mount plate bolt, hd rear end / differential cover, rear end / differential cover gasket, rear spring mount anchor plate, firewall insulation / carpet fastener, brake caliper, contact set & condenser kit, dynomax U bolt clamp, clutch rod boot, air filter, expansion plugs, engine block heater, engine heater, fuel pump gasket, univ af 3.78l, stop leak 296ml, steering column, spark plug, fuel kit, gasket, corvette 9 leaf spring, standard rear, rear spring mount plate bolt kit, differentail cover, differentail cover gasket rear, leaf spring mounting plate rear, gasket, wiper blade trico replacement, all gm decal, engine emission decal, dsadl lea/vin/hard plastic, gas cap, front 3/4 sway bar rubber bushing, carb kit, distributor cap, ignition coil, distributor rotor, fuel pump, spring cover/jet choke rod/choke coil spring, fan clutch, curved hose, curved hose, radiator, brake caliper, v-belt, transmission set, tachometer cable, paint. |
| Phone: 780-437-4046 |
 Click on the image for a larger picture. 
|